What size generator do you need for welding?
The amperage in a welder’s model name does not tell you how much power to supply. Read the input and output sides separately, then size for your actual machine and settings.

Welder sizing chart: published reference loads
| Reference model | AC input | Published input at rated output | Rated welding output |
|---|---|---|---|
| Hobart Handler 140 | 115V | 2,500W 2.9kVA · 20A listed | 90A at 18.5V DC 20% duty cycle |
| Hobart Handler 210 MVP 230V mode | 230V | 4,600W 5.4kVA · 24A listed | 150A at 23V DC 30% duty cycle |
Sources: Hobart sheet 217919, March 2016, page 2 (manufacturer-authored PDF, archived by Weld It U); Hobart sheet 250822, September 2022, page 2 (official PDF). The original Handler 140 website link returned 404 when checked on October 24, 2026. These are edition-specific references; check the manual for your machine.
The table preserves the documents’ separately listed current, kVA and kW. These figures describe rated welding points, not maximum input at the model’s highest output amperage. Do not infer full-output requirements by scaling the model name.
Why input watts and welding amps are different
For single-phase AC, input volts × input amps gives apparent power in VA. Real power in watts also depends on power factor. Use the manufacturer’s kW, kVA and current specifications together rather than treating VA as W.
A source can pass a watts check and still fail another requirement. Check its per-outlet and total current limits, voltage, connector compatibility, power-quality requirements and response to arc starts. A peak-watts label alone does not resolve these checks.
What our battery calculator can tell you
For the Handler 140 reference watts alone, our 10% continuous-output allowance gives a 2,750W preliminary inverter target. This is a calculation rule, not a manufacturer-approved generator size or a verified station-and-welder pairing.
A station with the right AC voltage and enough continuous watts is a candidate for further checks, including a suitable 240V-capable system. Confirm the exact voltage range, outlet current, kVA and welder requirements for each system.
Our calculator screens voltage, watts and battery energy. It does not model welder power factor, transient behavior, receptacles or per-outlet current, and we have not load-tested these pairings.
Runtime: arc-on time is not session time
Battery energy is spent during welding and between welds. Duty cycle describes the machine’s rated welding-and-cooling limits; it does not establish idle consumption or how much of your work session will actually be spent welding.
As a simplified energy example, a 2,000Wh battery with our 80% usable-energy assumption contains 1,600Wh for the load. At 2,500W, that is about 38 equivalent arc-on minutes, before idle consumption or other tools. It is not a continuous-welding permission or a predicted session duration.
Runtime arithmetic: 2,000Wh × 0.8 ÷ 2,500W × 60. Actual usable energy and consumption depend on the equipment and operating conditions. Follow the welder’s duty-cycle instructions.
Use the calculator for your reference setup
The jobsite welder scenario starts with the Handler 140 reference load, site lighting and phone chargers. Adjust the operating hours and devices to see how watts and battery energy change. Treat the product list as an initial specification screen.
Size your welding setup →Frequently asked questions
Will a 3000 watt generator run a welder?
A 3,000W rating alone does not establish compatibility. The Handler 140 reference input is 2.5kW and 2.9kVA at its rated welding output. Confirm input current, outlet limits, starting behavior and the welder manufacturer’s generator guidance before choosing a source.
Can you run a welder on a battery power station?
A suitable station may be a candidate, but voltage and continuous watts are only an initial screen. Its outlet current, apparent-power capability and response to the exact welder must also be checked. WattSizer has not tested these combinations.
What size generator for a 200 amp welder?
Use the exact model and operating setting. The Handler 210 MVP sheet lists 4.6kW and 5.4kVA input at its rated 150A welding output on 230V. That is not a maximum-input specification at 210A, or a universal requirement for every 200A-class welder.
Why are welders rated in amps but generators in watts?
Welding amps describe the output side. Source sizing uses the AC input voltage, current, real power and apparent power. For single-phase AC, volts times input amps gives VA; calculating real watts also requires power factor.