VA to Watts Calculator
Watts = VA × Power Factor
1,500 VA is 1,200W at power factor (PF) 0.8, or 1,500W at PF 1.0. PF 0.8 is an example assumption; use the equipment's documented or measured PF for your calculation. VA measures apparent power; for single-phase AC it equals RMS voltage × RMS current. Watts measure real electrical input power, and PF = W ÷ VA.
Updated · Arithmetic by definition; choosing the right PF is the real task, see guidance below.
VA to watts conversion table
| VA | PF 1.0 | PF 0.8 | PF 0.6 |
|---|---|---|---|
| 75 VA | 75W | 60W | 45W |
| 500 VA | 500W | 400W | 300W |
| 650 VA | 650W | 520W | 390W |
| 800 VA | 800W | 640W | 480W |
| 900 VA | 900W | 720W | 540W |
| 1,000 VA | 1,000W | 800W | 600W |
| 1,500 VA | 1,500W | 1,200W | 900W |
| 2,000 VA | 2,000W | 1,600W | 1,200W |
| 3,000 VA | 3,000W | 2,400W | 1,800W |
| 5,000 VA | 5,000W | 4,000W | 3,000W |
| 7,500 VA | 7,500W | 6,000W | 4,500W |
| 10,000 VA | 10,000W | 8,000W | 6,000W |
Why the two ratings exist
Inverters and generators carry both limits: a W rating for real power (engine/alternator capacity) and a VA or current rating for apparent power (wiring and semiconductor thermal limits). A 1,200W load at PF 0.8 draws 1,500VA — inside the W limit of a "1,200W" unit, but at its apparent-power edge. This is the same discipline our sizing engine applies: recorded VA startup demands (nameplate LRA × voltage) are screened against both limits and never silently equated with watts.
FAQ
What's the difference between VA and watts?
VA (volt-amps) is apparent power. Watts measure real electrical input power. Power factor is their ratio: PF = W ÷ VA. A motor drawing 1,500VA at PF = 0.8 consumes 1,200W of real input power; its mechanical output also depends on motor efficiency.
Why does this matter for generators?
Check both real-power output and apparent-power or current limits, along with voltage and startup capability. A 1,200W load at PF = 0.8 draws 1,500VA; a W-only label does not establish that a generator or inverter can supply it.
What power factor should I use?
Use a documented or measured PF for the equipment and operating load. A resistive heater can be modeled at PF = 1. Motor and electronic loads vary; the calculator's 0.8 default is an example, not a safe bound for unknown equipment. PF does not represent motor efficiency or predict startup surge.
How do I convert watts back to VA?
Divide by the same power factor: VA = W ÷ PF. 800W at PF 0.8 is 1,000VA. If you don't know the PF, you cannot convert — a range of plausible PFs (0.6–1.0) spans a 40% spread in the answer, which is why equipment documentation beats any default.
Is higher power factor better?
For the grid and the wiring, yes: higher PF means less current for the same real power. It is not a measure of equipment quality or efficiency — a PF 0.6 device is not "losing" 40% of its energy; the extra current returns to the source each cycle. What it does cost is current capacity in your inverter, extension cords and breakers.
Reference: Fluke's power factor definition. Updated .